CONDTROL Omniliner G3D - Instrukcja obsługi

1

EN User manual 1

DE Bedienungsanleitung 2

RU Руководство пользователя 3

PL

Instrukcja obsługi 4

Omniliner 3D/G3D

User manual

Cross line laser

EN

SAFE T Y INSTRUC TIONS
Attention!

This user manual is an essential part of this

product.

The user manual should be read carefully before you use the

product for the first time. If the product is given to someone

for temporary use, be sure to enclose user manual to it.

- Do not misuse the product;

- Do not remove warning signs and protect them from

abrasion, because they contain information about safe

operation of the product.

- Do not look into the laser beam or its reflection, with

unprotected eye or through an optical instrument. Do not

point the laser beam at people or animals without the need.

You can dazzle them.

- To protect your eyes close them or look aside.

- Always install the product in such a way, so that laser line is

below or above eye level.

- Do not let unauthorized people enter the zone of product

operation.

- Store the product beyond reach of children and unauthorized

people.

- It is prohibited to disassemble or repair the product yourself.

Entrust product repair to qualified personnel and use original

spare parts only.

- Do not use the product in explosive environment, close to

flammable materials.

- Laser intensive glasses are used for better recognition of the

laser beam, do not use them for other purposes. Laser glasses

do not protect from laser radiation as well as ultraviolet

radiation and reduce color perception.

- Avoid heating the batteries to avoid the risk of explosion and

electrolyte leakage. In case of liquid contact with skin, wash

it immediately with soap and water. In case of contact with

eyes, flush with clean water during 10 minutes and consult the

doctor.

PRODUCT DESCRIPTION

CCross line lasers Omniliner 3D/G3D CONDTROL are intended

to project vertical and horizontal planes. They project one

360° horizontal and two 360° vertical planes and provide

compensation of the slope up to ±4°.
The laser levels have 2 operating modes:

- Automatic leveling to compensate irregularities within

self-leveling range of ± 4°;

- Locked compensator, to project inclined planes and lines.

Pulse mode allows using laser receiver to increase the working

range of the laser level or to work when laser is hard to define

in bright lighting conditions.

The laser levels are suitable for use at both indoor and outdoor

building areas.

Omniliner 3D/G3D

6

1

2

3

4 5

1 - Laser lines exit window

2 – Control panel

3 – Battery cover

4 - Tripod thread 1/4’’

5 - Tripod thread 5/8’’

6 – Switch bar

7 – Hole for mounting on a screw/nail

Control panel

1. Switch on/off:

- The laser level

- laser lines

2. Switch on/off pulse mode

3. Power indicator

4. Indication of locked pendulum

5. Indication of pulse mode

DELIVERY PACKAGE

Laser level – 1 pc.

Battery – 2 pcs.

Charger – 1 pc.

Pouch – 1 pc.

User manual – 1 pc.

7

TECHNICAL SPECIFICATIONS

Omniliner 3D

Omniliner G3D

Working range/

with receiver

50 m/100 m

Self-levelling accuracy

±0,2 mm/m

Self-levelling range

± 4°

Self-leveling duration,

typically

<3″

Continuous working time

>10 hours

>5 hours

Working temperature

-10°C ... +50°C

Storage temperature

-20°C ... +70°C

OPERATION

Place the laser level on a firm and stable surface or a tripod.

Move the switch bar to select necessary operating mode:

1) Automatic leveling

Move the switch bar to unlocked position . H-line will
automatically switch on.
Short press button to switch on required laser lines.

If the laser level is out of the range of automatic compensation
laser lines will flash 1 time per second.
Short press button to switch on/off the pulse mode.
To switch off the laser level move the switch bar
to position .

2) Projection of inclined planes

Move the switch bar to locked position .

Press and hold during 3 seconds to switch on the laser.

Short press to switch on required laser lines.

Switched on laser lines will flash 1 time per each 5 seconds.
After all possible combinations of lines are switched on, the
next long press during 3 seconds will switch off the
laser level.
Long press during 3 seconds to switch on/off the pulse
mode.

Attention!

To increase the operating time and avoid the risk of

unintentional blindness switch the laser on only when you are
ready to make measurements.
If operated near objects or air streams with different from the
environment temperature the laser line may tremble due to
heterogeneity of the atmosphere. The longer is the distance,
the more trembling can be observed
The width of the laser line increases with the increasing of
the operating distance. The layout should be made along the
axis of the laser line. For maximum accuracy, use the middle
portion of the laser line.
It should be noted that the shape of the laser line on the
object’s surface (e.g., walls, ceilings, etc.) depends on the
curvature and tilt of the surface relative to the laser plane.

ACCURACY CHECK
Check of horizontal line

Use 2 parallel vertical walls which are located opposite each

other at a distance of 5 m.

1. Set the instrument close to the wall A (see Fig. A). Switch

on the vertical and horizontal laser emitters, unlock the

compensator. Turn the instrument in such a way so that the

laser lines intersecting each other are projected on the near

wall A opposite the instrument. Mark the point where laser

lines intersect each other as A1.

2. Turn the instrument by 180°, mark the point where laser

lines intersect each other on the opposite wall as В2. (see

Fig. В).

A

B

5. Measure distance d between points А1 and А3 (see. Fig. D).

If this distance exceeds 2 mm, please contact service center.

3. Move the instrument to the opposite wall B and set it in such

a way so that the point where laser lines intersect each other

would be on the same level with point B2.

C

D

Check of vertical line

Use a plumb bob as a reference of a vertical line. Place the

instrument at distance of 1,5m from the plumb bob.

1. Unlock the compensator, switch on the vertical laser line

and align it with the low point of plumb bob.

2. If deviation between the laser line and the plumb bob line

exceeds ±0.2 mm per 1 m of the plumb bob length (for a 2.5 m

plumb bob deviation shouldn’t exceed 0.5 mm) please contact

service center.

3. Turn the instrument by 180° and align the vertical laser line

with the low point of plumb bob once again.

4. Turn the instrument by 180°, direct the instrument to the

wall А in such a way so that the vertical line would coincide

with point А1. Mark the point of intersecting laser line on the

wall А as A3. (see. Fig. D).

CARE AND MAINTENANCE
Attention!

The product is an accurate optical mechanic device

and requires careful handling. Check the accuracy before

using.

Maintenance of the following recommendations will extend

the life of the device:

- Store the product, spare parts and its accessories beyond

reach of children and unauthorized people.

- The product should be transported only when compensator

is locked.

- Keep the product clean and protected from any bumps, dust

and dampness; do not allow getting moisture, dust or other

dirt inside of the product.

- In case if any moisture goes into the product, remove the

batteries and take it to the service center.

- Do not keep or use the device for a long time at high humidity

conditions.

- Carry out accuracy check regularly (see paragraph «Accuracy

check»).

- To clean the product use a soft wet cloth. Do not use harsh

chemicals, cleaning solvents or detergents.

- Сlean laser aperture periodically with a soft lint-free cloth

with isopropyl alcohol.

Mishandling of the following rules can cause electrolyte

leakage from the batteries or other damages:

- Remove the battery from the product if you do not use it for

a long time.

- Do not leave discharged battery in the laser level.

UTILIZATION

Expired tools, accessories and package should be passed

for waste recycle. Please send the product to the following

address for proper recycle:

CONDTROL GmbH

Wasserburger Strasse 9

84427 Sankt Wolfgang

Germany

Do not throw the product in municipal waste!

According to European directive 2002/96/ЕC expired

measuring tools and their components must be collected

separately and submitted to environmentally friendly recycle

of wastes.

WARRANTY

All CONDTROL GmbH products go through post-production

control and are governed by the following warranty terms. The

buyer’s right to claim about defects and general provisions of

the current legislation do not expire.

1) CONDTROL GmbH agrees to eliminate all defects in the

product, discovered while warranty period, that represent the

defect in material or workmanship in full volume and at its own

expense.

2) The warranty period is 24 months and starts from the date

of purchase by end consumer (see the original supporting

document).

3) The Warranty doesn’t cover defects resulting from wear

and tear or improper use, malfunction of the product caused

by failure to observe the instructions of this user manual,

untimely maintenance and service and insufficient care, the

use of non-original accessories and spare parts. Modifications

in design of the product relieve the seller from responsibility

for warranty works. The warranty does not cover cosmetic

damage, that doesn’t hinder normal operation of the product.

4) CONDTROL GmbH reserves the right to decide on

replacement or repair of the device.

5) Other claims not mentioned above, are not covered by the

warranty.

6) After holding warranty works by CONDTROL GmbH warranty

period is not renewed or extended.

7) CONDTROL GmbH is not liable for loss of profit or

inconvenience associated with a defect of the device, rental

cost of alternative equipment for the period of repair.

This warranty applies to German law except provision of the

United Nations Convention on contracts for the international

sale of goods (CISG).

In warranty case please return the product to retail seller or

send it with description of defect to the following address:

CONDTROL GmbH

Wasserburger Strasse 9

84427 Sankt Wolfgang

Germany

Laser radiation! Do not stare into beam

Class 2 laser

<1 mW 635 nm

EN60825-1: 2007-03

Cross line laser

Kreuzlinienlaser

EN
DE

Лазерный нивелир

RU

Laser krzyżowy

PL

Class 2 laser

<1 mW 520 nm

EN60825-1: 2007-03

1

2

4

3

5

Relative humidity

<90%

Dust and water

protection rate

IP65

Thread for mounting

on a tripod

1/4’’, 5/8’’

Laser type

Class II 635 nm

< 1 mW

Class II 520 nm

< 1 mW

Battery

3.7V 5200 mAh Li-ion

Dimensions

140х138х110 mm

Weight

- without battery

- with battery

660 g

774 g

BEFORE START OPERATION

Power supply

The cross line laser is powered via a 3.7V 5200 mAh Li-ion

battery included in the delivery package.

Install/charge the Li-ion battery

Install the battery in the battery compartment, observing the

polarity.

Use the battery included in the delivery package only.

If the power indicator on the control panel starts flashing red,

the battery must be charged.

The charging procedure is as follows:

1) Remove the battery from the laser level.

2) Connect the battery to the power source by the charger

included in the delivery package.

The power indicator on the charger will be red while charging.

3) The battery charging time is about 5 hours.

4) Once the power indicator on the charger turns green,

disconnect the charger and install the battery in the battery

compartment.

Omniliner 3D

Omniliner G3D