Hertz HMX 8-LD-TW - Instrukcja obsługi - Strona 18
Głośniki Hertz HMX 8-LD-TW – Instrukcja obsługi, czytaj za darmo online w formacie PDF. Mamy nadzieję, że to pomoże rozwiązać wszelkie problemy, które mogą się pojawić. Jeśli masz dodatkowe pytania, skontaktuj się z nami za pomocą formularza kontaktowego.
20
FUSE
FUSE
FUSE
FUSE
RED
GREEN
BLUE
YELLOW (+ 12 V)
+ 12 Vdc
Switched +12V
GND
*
250 mA
only for
HMS 10 S-LD-G
/
HMS 10 S2-LD-G
100 mA
or
*
250 mA
100 mA
or
*
250 mA
100 mA
or
*
250 mA
2 Speakers
1 Speaker
N Speakers
100 mA
x N Speaker
or
*
250 mA
x N Speaker
COLOR
RED GREEN BLUE
WHITE
X
X
X
RED
X
GREEN
X
BLUE
X
YELLOW
X
X
PURPLE
X
X
CYAN
X
X
LED CIRCUIT WIRING
-
Voltage provided to the LED circuit must
not exceed +12,5 Vdc
referred to the system ground
(GND)
.
-
Voltage provided to the LED circuit should be switched by an
activation circuit
in order to turn-on the LED lighting only when
required and turn it off when vessel is not used or put into storage.
-
Protect the
YELLOW (+12V)
wire with a 100mA fuse, then connect the
YELLOW (+12V)
wires from all the speakers together to the
main
Switched +12 Vdc
.
-
Fuse the
Switched +12 Vdc
according to the total number of speakers connected in parallel. We suggest for the fuse value to be as close
as possible to the standard value corresponding to 100mA or 250 mA x N speakers rounded in excess. I.e. 6 speakers (3 pairs) in parallel
requires 100mA x 6 = 600mA, for which the closest standard fuse value rounded in excess would be 630mA.
-
Connect the
R(Red), G(Green), B(Blue)
wires from the speaker to the system ground
(GND)
referring to the below table according
to the color desired among the 7 available options.
COLLEGAMENTO DEL CIRCUITO LED
-
La tensione fornita al LED
non deve superare i 12,5 Vdc
riferiti a massa
(GND)
.
-
La tensione fornita al LED dovrebbe essere controllata da un
circuito di attivazione (+12V Switched)
per accendere il LED solo
quando necessario e spegnerlo quando l’imbarcazione non viene utilizzata o rimessa.
-
Proteggere con un fusibile da 100mA il cavo
YELLOW (+12V)
, poi connettere insieme i cavi
YELLOW (+12V)
di tutti gli speaker
al circuito
di attivazione (+12V Switched)
.
-
Proteggere con un fusibile la tensione fornita dal
circuito di attivazione (+12V Switched)
, il valore del fusibile deve essere calcolato
con la formula 100mA o 250 mA x N Speaker con il risultato approssimato al valore di fusibile standard più vicino. Esempio 6 speaker
(3 coppie) in parallelo richiedono 100mA x 6 = 600mA per il quale il valore standard più vicino è 630mA.
-
Collegare i cavi
R(Red), G(Green), B(Blue)
dallo speaker al sistema di massa
(GND)
seguendo la tabella sotto in funzione del colore
desiderato tra i 7 disponibili.
HMX 6.5-LD
/
HMX 6.5-LD-C
/
HMX 6.5-LD-TC
/
HMX 6.5-LD-TW
/
HMX 6.5 S-LD
/
HMX 8-LD
/
HMX 8-LD-C
/
HMX 8-LD-TC
/
HMX 8-LD-TW
/
HMX 8 S-LD
/
HMS 10 S-LD-G
/
HMS 10 S2-LD-G
LED direct wiring
"Ładowanie instrukcji" oznacza, że należy poczekać, aż plik się załaduje i będzie można go czytać online. Niektóre instrukcje są bardzo obszerne, a czas ich ładowania zależy od prędkości Twojego internetu.
Inne modele głośniki Hertz
-
Hertz HEX6.5 M-C
-
Hertz HEX6.5 M-W
-
Hertz HEX6.5 S-LD-G
-
Hertz HEX6.5 S-LD-GOB
-
Hertz HMX 6.5 S-LD-G
-
Hertz HMX 6.5 S-LD-SW
-
Hertz HMX 6.5 S-LD-TC
-
Hertz HMX 6.5 S-LD-TW
-
Hertz HMX 6.5-TC
-
Hertz HMX 8-LD-TC